NARA 5SDH-2
NARA 5SDH-2
The values of all the parameters listed here are printed on stderr when the program starts, whether or not they were supplied on the command line.
This is optional, and will default to localhost or the current value of the DBMAN_HOST environment variable.
The offsets and scale values for each range are stored here if the file is present.
See the Scale* and Offset* RefNames in the Hall probe controller Database RefNames section for more information.
If the file does not exist and a pathname is specified on the command line when the program is started it is created.
This is a 1 bit control, nop/reset.
0.0
= nop
1.0 = reset
The control key should be set to Mom.
This parameter should be owned by whatever task HPBtask registers as and the permissions set for direct update by users and direct update for the owner.
This parameter should have a range of +/- 20000 or more if the units are in gauss or a range of +/- 2 if the units are in tesla.
The control key doesn’t matter.
This parameter should be owned by whatever task HPBtask registers as and the permissions set for none by users and direct update for the owner.
This parameter should have a range of +/- 100. The reading is in degrees Celsius.
The control key doesn’t matter.
This parameter should be owned by whatever task HPBtask registers as and the permissions set for none by users and direct update for the owner.
This is a two bit paramater. Valid values are:
0.0 - 0.3 tesla range.
1.0 - 0.6 tesla range.
2.0 - 1.2 tesla range.
3.0 - 3.0 tesla range.
The control key can be set to IncN, DecN, or IDecE. Usually IDecE is used.
This parameter should be owned by whatever task HPBtask registers as and the permissions set for direct update by users and direct update for the owner.
This parameter is not used with a single range probe and may be omitted.
Offset0 - 0.3 tesla range
Offset1 - 0.6 tesla range
Offset2 - 1.2 tesla range
Offset3 - 3.0 tesla range
The parameters should have a range of +/- 20000 or more if the units are in gauss or a range of +/- 2 if the units are in tesla.
The control key should be set to RSetK.
These parameter should be owned by whatever task HPBtask registers as and the permissions set for direct update by users and direct update for the owner.
When HPBtask starts the values for these parameters are taken from the configuration file if specified on the command line. If the file is not present the values are set to zero.
If the file is present and the datapoints do not exist in the database the values from the file are used to set the hall probe controller.
If the value is changed the configuration file is updated with the new value so that the values are remembered across restarts.
When using a single range probe only the Offset0 parameter is used regardless of the actual range of the probe. The rest of the Offset* parameters are not used and may be omitted from the database.
Scale0 - 0.3 tesla range
Scale1 - 0.6 tesla range
Scale2 - 1.2 tesla range
Scale3 - 3.0 tesla range
The parameters should have a range of +/- 10 or more. The units dimensionless.
The control key should be set to RSetK.
These parameter should be owned by whatever task HPBtask registers as and the permissions set for direct update by users and direct update for the owner.
When HPBtask starts the values for these parameters are taken from the configuration file if specified on the command line. If the file is not present the values are set to zero.
If the file is present and the datapoints do not exist in the database the values from the file are used to set the hall probe controller.
If the value is changed the configuration file is updated with the new value so that the values are remembered across restarts.
When using a single range probe only the Scale0 parameter is used regardless of the actual range of the probe. The rest of the Scale* parameters are not used and may be omitted from the database.
The switches inside of the hall probe controller are recommended to be set as follows:
SW1-1 - off - SW1-(1-5) position does not matter
SW1-2 - off
SW1-3 - off
SW1-4 - off
SW1-5 - off
SW1-6 - on - serial data format = 1 stop bit, no parity
SW1-7 - off -
SW1-8 - on -
SW2-1 - off - transmit mode = on demand only
SW2-2 - on - terminator = carriage return
SW2-3 - off - double terminator = disabled
SW2-4 - on - echo commands = yes
SW2-5 - on - field units = gauss
SW2-6 - on - units symbol = symbol after data
SW2-7 - on - digital filtering = on
SW2-8 - off - reset = off
Switches SW1-(6-8) are shown in the NEC default positions, one stop bit, no parity. They can be set to other positions if the user wishes to initialize the communications port differently.
The field units may be set for gauss or tesla depending on the database configuration. The program will process either type of message.
Digital filtering may be turned on or off depending on user requirements.
Reset on power up can be set for user preference.
Note that at this time the program reads the switch settings from the controller on startup. The program adjusts itself for the SW2 settings except for the transmit mode which must be "on demand" rather than "every measurement sent". The rest of the SW2 settings are meant as a guide.
HINT: 9600 baud is the E position on the baud rate switch.
Note also that the number of stop bits and the character bit length may need to be set.
Similiar settings should be programmed into the terminal server when using remote mode.
Note that the label will need to be quoted for the shell to treat it as a single argument.
It might be better if ResetSC where indirect update..
When the program is started it registers with dbman as HPBtask.
This program is presently debugged to work properly with v6.0b firmware. It is known that this program has firmware revision dependent code in it. This can’t be helped.
